IBM C9010-022 Exam Questions – Secret To Pass In First Attempt

The IBM AIX Administration V1 C9010-022 practice test software offers you customizable learning so that you can estimate the time required to attempt each question as well as can get acquainted with the pattern of each question and solves the IBM C9010-022 AIX V1 CERTIFICATE exam with full confidence to win. No need to think much of it interface IBM C9010-022 exam pratice test software and pattern just download free demo and everything will be clear. Pay through MacAfee Secure payment method to get the instant access of the IBM C9010-022 exam questions.

C9010-022 PDF dumps; C9010-022 exam dumps:: https://www.dumpsschool.com/C9010-022-exam-dumps.html (62 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate IBM C9010-022 Dumps Exam Questions and Answers:

Version: 8.0
Question: 21

An administrator notices that the ntp group subsystem is not starting up at boot time. What will cause this issue?

A. The /etc/ntp.conf file has the following line commented out
broadcastserver
B. The following line is commented outinthe/etc/inetd.conf file:
ntp 123/tcp # Network Time Protocol
C. The following line is commented out of the /etc/inittab file:
xntpd: 23456789: respawn:/usr/sbin/xntpd > /dev/console 2>&1 #Start ntp daemon
D. The /etc/rc.tcpip file has the following line commented out:
start /usr/sbin/xntpd “$src_running”

Answer: D

Question: 22

An administrator is required to implement resource control for a running system WPAR called “skippy’. Which flag of the chwpar command will set the CPU Resource control limits for this WPAR to a minimum of 8%. a desired of 35% and a maximum of 45%?

A. chwpar -c CPU=8%-35%,45% skippy
B. chwpar-R CPU=8%-35%,45% skippy
C. chwpar-L CPU=8%-35%,45% skippy
D. chwpar-r PROC=8%-35%,45% skippy

Answer: D

Question: 23

New Updated C9010-022 Exam Questions C9010-022 PDF dumps C9010-022 practice exam dumps: https://www.dumpsschool.com/C9010-022-exam-dumps.html

A host has a single virtual Ethernet adapter (ent0) configured with only a default PVID, and the administrator is trying to determine why it cannot be used to reach any other system on the network. He suspects that it may be caused by a problem in the VLAN configuration.
How would the administrator determine the VLAN for which the adapter was configured?

A. Use the command ‘Isdev -I ent0’ on the host to determine the port VLAN ID.
B. Use the command ‘Isattr-EI ent0’ on the host to determine the port VLAN ID.
C. Look on the HMC to determine which VLAN is configured for the adapter.
D. Examine the Shared Ethernet Adapter on the Virtual I/O Server to determine which VLAN the adapter is using.

Answer: C

Question: 24

How can an administrator disable Role Based Access Control (RBAC) in a WPAR?

A. Run chattr -E -I sys0 -a enhanced_RBAC=false
Reboot the WPAR
B. Run the RBAC wizard and deselect ‘Enable RBAC
Reboot the system
C. Run chdev -I mywpar -a enhanced_RBAC=false
Reboot the Global Environment
D. Run chwpar -a RBAC=false
Reboot the WPAR

Answer: C

Question: 25

After performing a NIM rte install, the administrator noticed that not all filesets are at the correct Technology Level (TL). What action will help the administrator determine why the inconsistent fileset levels were installed?

A. On the NIM server, run an Ippchk to identify if the Software Vital Product Data is valid.
B. On the NIM client, run oslevel command against the TL to identify missing prerequisites.
C. Run instfix command on NIM client to determine what filesets are inconsistent.
D. On the NIM server run the NIM IsIpp command to indentify downlevel filesets contained in the lpp_source.

Answer: D

Question: 26

What is a requirement for Live Partition Mobility?

A. The network and disk must be virtual.
B. The disk must be virtual and a Logical Host Ethernet Adapter (LHEA) for network.
C. The client partition must be connected to a SAN.
D. The client partition must be set up as a ‘Mover Service Partition’.

Answer: A