Dell DNDNS-200 Exam Questions – Secret To Pass In First Attempt

The Dell Networking Professional DNDNS-200 practice test software offers you customizable learning so that you can estimate the time required to attempt each question as well as can get acquainted with the pattern of each question and solves the Dell DNDNS-200 Dell Certified Professional CERTIFICATE exam with full confidence to win. No need to think much of it interface Dell DNDNS-200 exam pratice test software and pattern just download free demo and everything will be clear. Pay through MacAfee Secure payment method to get the instant access of the Dell DNDNS-200 exam questions.

♥ VALID DNDNS-200 Exam Questions 2018 ♥

DNDNS-200 exam questions, DNDNS-200 PDF dumps; DNDNS-200 exam dumps:: https://www.dumpsschool.com/DNDNS-200-exam-dumps.html (60 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest Dell DNDNS-200 Dumps Exam Questions and Answers:

Version: 8.0
Question: 21

A network engineer is verifying the configuration of a LAG connection on an S-Series switch.
Which two commands should the network engineer use to determine the operation of the LAG? (Choose two.)

A. show lacp
B. show interface C. show port-channel-flow
D. show uplink-state-group

Answer: A,B

Question: 22

Refer to the exhibits.
A networking engineer is unable to ping from VLAN 30 across two S-Series switches. Port 13 on switch Dell1 and Port 43 on switch Dell2 both have a link status of up.
Why does the ping fail between the two switches?

A. Dell1 switch VLAN 30 interface is down.
B. Dell2 switch VLAN 30 interface is down.
C. Dell2 switch port 44 is misconfigured as Untagged.
D. Dell2 switch port 43 is misconfigured as Tagged.

Answer: D

Question: 23

Refer to the exhibit.
A network engineer is called onsite to troubleshoot replication failure and traffic loss. Whenever replication occurs between SAN A and SAN B, users report traffic loss between sites, and replication ultimately fails due to traffic loss.
Based on the topology shown, what is the most likely cause of the traffic loss?

A. Traffic needs to be policed on the site border routers.
B. An inbound policy map needs to be defined on the site border that marks the replication traffic with a DSCP value of 46.
C. An outbound policy map needs to be defined on the site border that marks the replication traffic with a DSCP value of 46.
D. Traffic needs to be shaped on the site border routers.

Answer: C

Explanation:
In Quality of Service, DSCP value 46 is high-priority traffic.

Question: 24

Refer to the exhibit of the N-series switches.
The exhibit shows a Layer 2 network between Host A (a Desktop Computer running Windows 7) and Host B (another Desktop Computer running Windows 7) and the list of VLANs Untagged (U) and Tagged (T) at each Ethernet interface: Host A transmits an Ethernet frame untagged on VLAN 1.
What will happen to the Ethernet frame?

A. SW2 drops the Ethernet frame when trying to transmit it out of interface E2 because the incoming and outgoing interfaces are Tagging/Untagging VLAN 1 differently.
B. The Ethernet frame is successfully delivered to Host.
C. STP drops the Ethernet frame because it cannot create an end-to-end loop free path between the switches for VLAN 1.
D. VLAN consistency protocol determines that the VLAN is not correctly Tagged/Untagged on all interfaces, an error will occur, and SW1 will drop the frame on interface E2.

Answer: B

Question: 25

Refer to the exhibit.
Considering the network topology and information shown, what is an issue with end point devices in network 192.168.102.0/24 that try to route to 192.168.101.0/24?

A. ICMP Redirects
B. Suboptimal Routing
C. Routing Loop
D. Summarization Black Hole

Answer: C

Question: 26

Refer to the Exhibit.
A network engineer receives the output shown when removing MLAG from a pair of N-Series switches.
Which sequence of steps must the engineer complete to remove the vpc peer-link from Port Channel 1?

A. Shut down the Port Channel interfaceIssue the no vpc peer-link command on the Port Channel
B. Remove the vpc feature using the no feature vpc commandIssue the no vpc peer-link command on the Port Channel
C. Remove the channel-group command from all members of the Port ChannelIssue the no vpc peer-link command on the Port Channel
D. Remove peer-keepalive enable using the no peer-keepalive enable commandIssue the no vpc peer-link command on the Port Channel

Answer: D

New Updated DNDNS-200 Exam Questions DNDNS-200 PDF dumps DNDNS-200 practice exam dumps: https://www.dumpsschool.com/DNDNS-200-exam-dumps.html