Cisco 642-887 Exam Questions – Secret To Pass In First Attempt

The Cisco Implementing Cisco Service Provider Next-Generation Core Network Services 642-887 practice test software offers you customizable learning so that you can estimate the time required to attempt each question as well as can get acquainted with the pattern of each question and solves the Cisco 642-887 Cisco Certified Network Professional Service Provider CERTIFICATE exam with full confidence to win. No need to think much of it interface Cisco 642-887 exam pratice test software and pattern just download free demo and everything will be clear. Pay through MacAfee Secure payment method to get the instant access of the Cisco 642-887 exam questions.

♥ VALID 642-887 Exam Questions 2018 ♥

642-887 exam questions, 642-887 PDF dumps; 642-887 exam dumps:: (184 Q&A) (New Questions Are 100% Available! Also Free Practice Test Software!)

Latest and Most Accurate Cisco 642-887 Dumps Exam Questions and Answers:

Version: 10.0
Question: 1

Which three conditions can occur when metering traffic using a dual token bucket traffic policing QoS
mechanism on Cisco routers? (Choose three.)

A. conform
B. pass
C. violate
D. exceed
E. burst
F. matched

Answer: A, C, D

Question: 2

What is the correct formula for determining the CIR?

A. CIR = Bc/Tc
B. CIR = Bc x Tc
C. CIR = Tc/Bc
D. CIR = Bc + Be
E. CIR = Tc/(Bc+Be)
F. CIR = (Bc+Be)/Tc

Answer: A

Committed Information Rate (CIR) – the rate the device will send at (on average) over a one second
The default CIR when traffic-shaping is enabled on the interface is 56K. CIR is also referred to as the
“target rate”. Since the device is forced to send at the AR, it does not send all of the time (within one
second) Â in order to send an average amount of data that equals the CIR.
Minimum CIR (mincir) – the rate the service provider guarantees to accept. Theoretically, the
provider will set the DE bit for all traffic above this rate. Mincir is designed to be used in conjunction
with adaptive shaping. With adaptive shaping, the router will throttle down in the event of
congestion. The router will not throttle down below this value.
Committed Burst (Bc) – the number of committed bits allows to be sent during a given interval. The
device sends an average amount of traffic to achieve the CIR. The Bc value defaults to 1/8 of the
configured CIR for speeds below 650K. For speeds above that, it is roughly 1/16 of CIR.
Excess Burst (Be) – the number of non-committed bits the router is allowed to send above Bc during
the first interval (Tc). The amount of Be “credits” is derived from unused Bc credits in previous
intervals. There is no limit to how long Be can “store” unused Bc credits. It is a common
misconception that Be can only store credits from the previous interval or the previous second. There
is no default Be value.
Committed Rate Measurement Interval (Tc) – the time interval over whic Bc or Bc+Be can be
transmitted. The max value is 125 ms and the minimum value is 10 ms.
The Formula
CIR, Tc, and Bc are related mathematically by the following formula:
CIR = Bc/(Tc/1000) Notice the division of Tc by 1000 is used to convert milliseconds into seconds – the common measurement of CIR and Bc.

Question: 3

DS-TE implementations on Cisco routers support which bandwidth pool(s) and class type(s)?
(Choose two.)

A. global pool only
B. subpool only
C. global pool and subpool
D. class-type 0 only
E. class-type 1 only
F. class-type 0 and class-type 1
Answer: C, F

Differential Service Tunnels
Differential Service Traffic Engineering (TE) is an extension of the regular MPLS Traffic Engineering
(MPLSTE) feature. Regular TE does not provide bandwidth guarantees to different traffic classes. A
single bandwidth pool (global pool) is used in regular TE that is shared by all traffic. In order to
support various class of service (CoS), the ability to provide multiple bandwidth pools is required.
These bandwidth pools then can be treated differently based on the requirement for the traffic class
using that pool.
In RSVP global and subpools reservable bandwidths are configured on a per interface basis to
accommodate TE tunnels on the node. Available bandwidth from all configured bandwidth pools is
advertised using Interior Gateway Protocol (IGP). RSVP is used to signal the TE tunnel with
appropriate bandwidth pool requirements.

Question: 4

Which field in the MPLS shim header is used to support different QoS markings?

A. IP precedence
D. ToS
E. S
F. Label

Answer: C

MPLS EXP Marking
The three MPLS EXP (experimental) bits in the shim header of an input or output MPLS packet
header may be set or changed by a user configured value

Question: 5

On a Cisco IOS XR router, which mechanism protects the router resources by filtering and policing the
packets flows that are destined to the router that is based on defined flow-type rates?

C. Committed Access Rate
D. Control Plane Policing
E. Management Plane Protection
F. NetFlow

Answer: B

Local Packet Transport Services (LPTS) maintains tables describing all packet flows destined for the
secure domain router (SDR), making sure that packets are delivered to their intended destinations.
The Low Latency Queueing feature brings strict priority queueing to Class-Based Weighted Fair
Queueing (CBWFQ).

Question: 6

When configuring LLQ (strict priority queue) on a traffic class using the Cisco IOS XR priority
command on a Cisco ASR9K router, which additional QoS command is required for this traffic class?

A. shape
B. police
C. random-detect
D. bandwidth

Answer: B

The Low Latency Queueing feature brings strict priority queueing to Class-Based Weighted Fair
Queueing (CBWFQ).

New Updated 642-887 Exam Questions 642-887 PDF dumps 642-887 practice exam dumps: