Cisco 200-601 Exam Questions – Secret To Pass In First Attempt

The Cisco Managing Industrial Networks for Manufacturing with Cisco Technologies 200-601 practice test software offers you customizable learning so that you can estimate the time required to attempt each question as well as can get acquainted with the pattern of each question and solves the Cisco 200-601 Cisco Certified Network Associate Industrial CERTIFICATE exam with full confidence to win. No need to think much of it interface Cisco 200-601 exam pratice test software and pattern just download free demo and everything will be clear. Pay through MacAfee Secure payment method to get the instant access of the Cisco 200-601 exam questions.

Version: 9.0
Question: 1

Which command globally enables QoS on a Cisco Industrial Ethernet switch?

A. switch(config)#qos enable
B. switch(config)#mls queuing enable
C. switch#enable queuing
D. switch(config)#mls qos

Answer: D

Question: 2

To ensure ProfiNET Layer 2 Class-of-Service markings from ProfiNET devices are trusted by the switch, which command must be entered on the interface attached to the device?

A. switch(config-if)#mls qos trust cos
B. switch(config-if)#qos trust cos
C. switch(config-if)#profinet cos trust
D. switch(config-if)#trust qos cos

Answer: A

Question: 3

New Updated 200-601 Exam Questions 200-601 PDF dumps 200-601 practice exam dumps: https://www.dumpsschool.com/200-601-exam-dumps.html(70 Questions)

Refer to the exhbit. Which three elements would enable high availability and predictable performance for a motion control application spread across two switches (with video and I/O traffic)? (Choose three)

A. Configure QoS to give PTP traffic the highest priority
B. Fiber optic uplinks
C. Redundant uplinks
D. Configure QoS to give I/O traffic the highest priority
E. Copper uplinks
F. Interconnect the two switches

Answer: A, B, C

Question: 4

You have been tasked to design an Ethernet network capable of Motion control with cycle times not to exceed 1ms. In order to create a more deterministic network, what characteristic/s should you primarily focus on?
A: Lattency and Jitter
B: Redundancy and high availability
C: Explicit and Implicit messaging
D: This cycle time is not possible on an Ethernet network
E: Gigabit port speed
Answer: A

Question: 5
Refer to the exhibit.

CIP Implicit messages from I/O#1 are being marked IP DSCP 47 by the endpoint and this marking is trusted by L2SW4. L2SW4 is configured to map DSCP 47 to output queue 1 threshold 1. You have received feedback that some of these messages are not being received. Executing the show mls interface GigabitEthernet statistics command on L2SW4 results in:
L2SW4# show mls interface GigabitEthernet 1/1 statistics

output queues dropped:
queue: threshold1 threshold2 threshold3
queue 0 0 0 0
queue 1 309232345 450 0
queue 2 300 10 0
queue 3 91 0 0
Repeating this command results in the counters incrementing for queue 1 threshold 1. What are two options for reducing the packet loss on this interface while preserving the end-to-end DSCP marking? (Choose two)

A. Configure I/O#1 to mark this traffic with a different DSCP that is mapped to a less congested queue
B. Increase the buffer allocation for input queue 1
C. Increase the buffer allocation for output queue 1
D. Alter the service policy to police to a higher CIR
E. Change the egress queue map on L2SW4 to map this traffic to a less congested queue

Answer: C, E

Question: 6

It is common to use Resilient Ethernet Protocol (REP) on the manufacturing floor as a resiliency protocol, as opposed to the Enterprise where it is not generally deployed. What are two reasons why REP is more suitable for the plant floor? (Choose two)

A. REP is only supported on Industrial Ethernet switches, it is not supported on Catalyst switches.
B. REP converges faster than Spanning Tree, allowing for greater network availability.
C. REP supports Industrial Ethernet protocols better because it moves the packets faster.
D. Running dual cables from access switches to an aggregation switch can have a much higher cost on the plant floor than in the Enterprise and running a ring protocol like REP provides resiliency at a lower cost.
E. Industrial protocols can be negatively impacted by the number of nodes the Ethernet frame traverses, REP provides a topology with no more than 3 nodes for any data path.

Answer: B, D